Well Pump and Septic Electrical in Wesley Chapel, FL
Pump Circuits, Pressure Switches, and Septic Alarms|Licensed & Insured, EC13011268
Kennedy Electric runs and repairs the power for private wells, septic pumps, and lift stations at Wesley Chapel homes. We wire each circuit between the panel and the equipment, and when a pump goes quiet, we test that circuit stop by stop along the water's path.
Mention if the taps are dry right now and if a breaker has tripped.
Call (352) 251-2795, Monday through Friday, 8 a.m. to 4 p.m., or send a request online. Calls after hours are returned the next business day.
At a glance
Wesley Chapel Houses That Run on a Private Well
Some Wesley Chapel homes still pump their own water. Around Quail Hollow, one of the town's older semi-rural areas, the Quail Hollow Alliance reports that county utility staff found no public water or sewer available in its neighborhoods, and it says plainly that “the majority of us are on well and septic.” In a house like that, the pump circuit is the water supply: if its breaker, buried wire, or tank switch fails, the tap runs dry.
A house's drinking-water well has to stand at least 75 feet from any septic tank and drainfield under the water management district's well rules. With the well and the tank that far apart, the buried run to the well, or to a septic pump tank where there is one, tends to be long. Voltage drops along a long run, so the wire is sized for the distance as well as the pump.
How it runs
Wiring a New Pump Alongside the Other Trades
On a new house, or a replacement home going onto a lot with a well and septic, the electrical work runs in step with two other contractors. Before the county issues the permanent power release, the septic final has to show as passed right beside the electrical final.
-
1
The pump and tank go in first
A well contractor sets the pump, its drop pipe, and the pressure tank. The voltage and horsepower on the pump's label size the breaker and the wire.
-
2
The circuits go in under a permit
The pump circuit runs from the panel to a disconnect at the well, then on to the pressure switch and any control box. A septic pump tank's pump and alarm circuits can follow once the septic contractor has set the tank. Some builders file the permit themselves. When one doesn't, the permit falls to Kennedy Electric, along with each inspection it calls for.
-
3
Both finals clear, then the water runs
Once the power is on, the electrician runs the pump through full cycles and watches the pressure switch cut in and out.
What we cover
Following the Water Across a Well-and-Septic Lot
On a well-and-septic lot, water loops from the ground, through the house, and out to the septic system. Power meets it at each stop, and each stop has its own place where that power can quit.
Down the well: the pump's supply
The water's path starts at the bottom of the well, where the pump sits and its cable climbs to the wellhead. Traced back from there, the power runs through a disconnect beside the casing, along a buried run, and back to a breaker of its own in the panel, usually a 240-volt one. A corroded splice, a shovel strike on that run, or a tripped breaker leaves the tap as dry as a worn-out motor would.
At the pressure tank: the switch that starts the pump
Up at the tank, the water meets the switch that decides when the pump runs, and, for a three-wire pump, the separate box with the parts that start the motor. Both covers hide live 240-volt terminals, so they stay shut until an electrician opens them. When the tank's pressure has dropped, power reaches the switch, and none leaves it, the switch or the wiring around it is where to look.
The irrigation well and its relay
A sprinkler well can have a pump of its own, started by a relay or contactor that the irrigation controller closes on the watering day. That relay, the low-voltage wire from the controller, and the pump circuit are electrical work.
Out to the septic tank: the pump and its alarm
If the septic design includes a pump tank, it needs a pump circuit and power for its high-water alarm. That alarm has to be both heard and seen where the household will notice it, under Florida's septic rules, and one mounted outdoors has to be waterproof and made for outdoor use. If rain or floodwater reached the alarm or the pump's disconnect, don't turn either one back on until it has been checked. A device that sat in water is replaced.
Where a lift station takes over
Where the drain field sits higher than the house, the water's path ends uphill, and a lift station's pump does the climbing. Its power can quit at the alarm and control panel, at the disconnect, or anywhere along its pump circuit, the same as at a septic pump tank. Our lift station work covers these residential pump circuits.
At every stop, our part is the power: we run it, repair it, and trace it. We don't repair or replace well pumps, and the tank, the well, and the septic system stay with their own contractors.
Pricing
What Sets the Price of Well and Septic Wiring
Whether the panel has room for another breaker, the circuit the pump's label calls for, and how long each buried run is all change the price.
Custom homes and large or multi-phase projects are estimated as soon as we can, or on the timeline your project sets.
Repair and troubleshooting visits are billed by the hour from arrival: $100 residential, $150 commercial, one-hour minimum, then half-hour increments, plus materials. No trip charge and no service fee. No hidden fees: the 3.5% surcharge on card and ACH payments is listed in our terms.
We don't do upfront pricing. No job has a standard price with us: each one is tailored to the property and the work you've asked for, and priced once we've seen it.
We offer free estimates on installs, upgrades, and replacements in our service area. Estimates aren't free when the job needs troubleshooting or testing to price, falls after hours or outside our service area, needs several meetings to gather information, or is new construction or a custom remodel with multi-party walk-throughs. For most jobs, estimates arrive by email by the end of the next business day, and quotes are good for 30 days.
Our warranty
05If something we installed fails because of our workmanship within 30 days of completion, we waive the hourly labor to put it right. Materials Kennedy Electric purchases for your job carry the manufacturer's one-year warranty. To replace defective materials we supplied, or materials damaged by storm, flood, fire, or other acts of God, we charge a reduced warranty labor rate of $50 an hour residential and $75 an hour commercial. The warranty does not cover materials not purchased by Kennedy Electric, work performed by the customer, or materials the customer purchased or damaged. Our warranty terms are printed on the estimate, the invoice, and the receipt, and the product boxes stay with you so you can register each product with its manufacturer.
Our Wesley Chapel taps are dry. Does it matter if the well pump is two-wire or three-wire?
The sprinkler well at our Wesley Chapel house keeps running after the watering cycle ends. Is that electrical?
Our well pump clicks on and off every few seconds. Is that an electrical fault?
We're pouring a driveway over the line that runs out to our well. Does the wire have to move?
If our house ever connects to county water, what happens to the well pump circuit?
Reviews
Well and Septic Circuit Jobs, Unvarnished
Straight from Google, in our customers' own words.
Request service
Request Well and Septic Power Work in Wesley Chapel
Say whether the job involves a well pump, a septic tank, or a lift station. Our office will reach you during business hours.